Step 1. Pop your ride’s hood

Of course, the first step is to op open the hood. Before you get to the headlight, you will first have to get access to it.  To do this, find the hood release switch next to the driver’s switch. Tug this with your finger to unlock the hood. After tugging the switch, go to the hood and lift it up. You’re supposed to find a piece of metal rod folded down under the hood. This is supposed to hold your hood up while you’re working. Set the hood on this rod.

Find the hood release switch next to the driver’s switch.

Step 2. Remove or disconnect your vehicle’s battery

You need to first disconnect the battery. Although electrical accidents in vehicles are rare, that doesn’t mean it can’t happen. It’s always better to be sure.

First, locate the battery. Then, use a socket wrench and loosen the nut on the battery’s negative terminal. Once you have the nut lose, pull the black cable to remove it from the battery. Put this at the side of the battery. Make sure this does not touch the terminal or the car. The positive terminal can be left as it is.

Step 3. Remove your car’s trims

These are usually for design purposes but they cover the headlights so you will have to remove them. They are held in place with plastic clips that you will have to unlatch. Be careful when removing them because the plastic may be thin and brittle and you may cause further damage.

If you break the clips off, you can usually get a replacement. These are available at auto-supplies stores and are fairly affordable.

Step 4. Unplug the headlight’s wire pigtail

The headlight’s wire pigtail is the plug where all the multi-colored wires can be seen. It is easy to unlatch or remove this by pressing on the small plastic release on the wire. Remember to keep the pressure on the clip as you disconnect it. Be careful not to tug the pigtail wire or you may break it. After you unplug it, look at the wires inside the plug. Try to notice if it has burn marks or as a burnt odor. If it does, there may be a problem with your car’s electrical system.

Step 5. Reach for the old headlight

Once you gained access to your headlight, twist it and tug it backward. The headlight should be twisted in a counter-clockwise direction to release it safely.  If you can’t seem to remove the bulb, don’t force it. You may end up damaging your vehicle or hurt yourself. Instead, take a step back and refer to your vehicle’s manual. It is the best reference in case you don’t know what to do.

Once you gained access to your headlight, twist it and tug it backward

Step 6. Get new headlights bulb

Now that your headlight is empty, it’s time to buy a replacement. You can opt to buy two bulbs and replace both headlights even though only one is broken. This will make sure that your headlights are uniformed.

This is when all details about your vehicle is needed. Do not even attempt to miss anything out. When buying a light bulb, inform the attendant about what model, make and year your car is. This will make sure that the bulb you receive is 100 percent compatible with your car.

Step 7. Take the bulb out of the box

Carefully remove the light bulb out of the box without making contact with your hands. The oil produced by your skin can damage modern types of light bulbs. That’s why it’s the best to top to wear safety gloves while doing this.

The broken headlights can be extremely dangerous

Step 8. Wipe the bulb with alcohol

If you happen to accidentally touch the light bulb, you can clean it with rubbing alcohol. Do not pour the alcohol directly onto the bulb. Take a clean rag or cotton. Dampen this with the rubbing alcohol. Now, gently wipe the bulb to remove the oil from your fingers. This will prolong the service life of the bulb.

If you don’t have a clean pair of gloves, cover your hands with a rag. This will let you touch the bulb without having to touch it directly with your hands. Remember to let your light bulb dry first before doing the next steps.

Step 9. Put the new light bulb in place

Slide the new light bulb where you removed the old one. After that, twist the bulb in a clockwise direction to keep it in place. Be very careful not to drop the bulb or the plastic casing. You will usually need to turn the new bulb a quarter way around to secure it in place.

Step 10. Do the steps in reverse

Once you have placed the new bulb, just repeat the steps in reverse.

All the BIGGEST brands are here at the country's LARGEST car accessories chain store, we offer global brands such as; Sparco, DUB, MicroMagic, Goodyear, Polaroid, Mothers, Pioneer, Pertua, Chupa Chups and many more.